Grade X5NiCrTiMoVB 25-15-2
European Standard Steel Grade 1.4606
Corresponding Standard EN 10088-3-2014
Stainless steels-Part 3: Technical delivery condition for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
Classification Precipitation-Hardening Stainless Steel
Properties Corrosion Resistance
Density 7.9 g/cm3
X5NiCrTiMoVB 25-15-2 Chemical Element Composition Content (%)
Component C Si Mn P S Cr Ni Mo Ti V B Al
Minimum Value - - 1 - - 13 24 1 1.9 0.1 0.001 -
Maximum Value 0.08 1 2 0.025 0.015 16 27 1.5 2.3 0.5 0.01 0.35
X5NiCrTiMoVB 25-15-2 Mechanical Properties
condition Heat Treatment or Condition
Tensile Strength
σb
Mpa
Yield Point
σs
Mpa
Elongation or Extension Rate
δ
%
Hardness
HBW
Impact Energy Absorption
KV2
J
Bar, rod, wire, section, bright products; d≤50 +AT ≤700 ≥250 ≥35 ≤212
Bar, rod, wire, section, bright products; d≤50 880 880~1150 ≥550 (long.)
≥20
(long.)
≥50
Cold drawn, precision bar; d≤10 +P880 950~1200 ≥750 ≥15 ≥30
Cold drawn, precision bar; 10<d≤16 +P880 950~1150 ≥750 ≥15 ≥30
Cold drawn, precision bar; 16<d≤40 +P880 900~1150 ≥600 ≥18 ≥40
Cold Drawn, Precision Finished Bar; 40<d≤50 +P880 880~1150 ≥550 ≥20 ≥40
Cold drawn, precision bar; d≤10 +A ≤850 ≤240
Cold drawn, precision bar; 10<d≤16 +A ≤800 ≤230
Cold drawn, precision bar; 16<d≤40 +A ≤800 ≤230
Cold Drawn, Precision Finished Bar; 40<d≤50 +A ≤700 ≤212
Cold drawn wire; d≥0.05 +C500 500~700
Cold drawn wire; d≥0.05 +C600 600~800
Cold drawn wire; d≥0.05 +C700 700~900
Cold drawn wire; d≥0.05 +C800 800~1000
Cold drawn wire; d≥0.05 +C900 900~1100
Cold drawn wire; d≥0.05 +C1000 1000~1250
Cold drawn wire; d≥0.05 +C1100 1100~1350
Cold drawn wire; d≥0.05 +C1200 1200~1450
Cold drawn wire; d≥0.05 +C1400 1400~1700
Cold drawn wire; d≥0.05 +C1600 1600~1900
Cold drawn wire; d≥0.05 +C1800 1800~2100
Cold drawn wire; 0.5<d≤1 +AT ≤1100 ≥10
Cold drawn wire; 1<d≤3 +AT ≤1050 ≥10
Cold drawn wire; 3<d≤5 +AT ≤1000 ≥10
Cold-drawn wire; 5<d≤16 +AT ≤950 ≥15

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!