中文版
Home Material DIN EN 10088-3-2014
简体 | 繁體
Grade X2CrNiMoN22-5-3
Germany W-Nr. 1.4462
Corresponding Standard DIN EN 10088-3-2014
Stainless steels – Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
Classification Duplex Stainless Steel
Properties Corrosion Resistance
X2CrNiMoN22-5-3 Chemical Element Composition Content (%)
Component C Si Mn P S Cr Ni Mo N
Minimum Value - - - - - 21 4.5 2.5 0.1
Maximum Value 0.03 1 2 0.035 0.015 23 6.5 3.5 0.22
① Elements not quoted in this table shall not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would impair mechanical properties and the suitability of the steel.
X2CrNiMoN22-5-3 Mechanical Properties
condition Heat Treatment or Condition
Tensile Strength
σb
Mpa 		Yield Point
σs
Mpa 		Elongation or Extension Rate
δ
% 		Hardness
HBW 		Impact Energy Absorption
KV2
J
Bar, rod, wire, section, bright products; d≤160 +AT 650~880 ≥450 (long.)
≥25		 ≤270 (long.)
≥100
Cold drawn, precision bar; d≤10 +AT 850~1150 ≥650 ≥12
Cold drawn, precision bar; 10<d≤16 +AT 850~1100 ≥650 ≥12
Cold drawn, precision bar; 16<d≤40 +AT 650~1000 ≥450 ≥15 ≥100
Cold drawn, precision bar; 40<d≤63 +AT 650~1000 ≥450 ≥15 ≥100
Cold drawn, precision bar; 63<d≤160 +AT 650~880 ≥450 ≥25 ≥100
Cold drawn wire; d≥0.05 +C800 800~1000
Cold drawn wire; d≥0.05 +C900 900~1100
Cold drawn wire; d≥0.05 +C1000 1000~1250
Cold drawn wire; d≥0.05 +C1100 1100~1350
Cold drawn wire; d≥0.05 +C1200 1200~1450
Cold drawn wire; d≥0.05 +C1400 1400~1700
Cold drawn wire; d≥0.05 +C1600 1600~1900
Cold drawn wire; d≥0.05 +C1800 1800~2100
Cold drawn wire; 0.5<d≤1 +AT ≤1050 ≥20
Cold drawn wire; 1<d≤3 +AT ≤1000 ≥20
Cold drawn wire; 3<d≤5 +AT ≤9500 ≥25
Cold-drawn wire; 5<d≤16 +AT ≤900 ≥25
+AT=solution annealed；+A=annealed；+QT = quenched and tempered；+P=precipitation hardening；+C=Cold worked，+Csuffix followed by a number represents the tensile strength grade, i.e., the minimum tensile strength value.
long.=longitudinal；tr.=transverse
d=diameter or thickness；Unit mm
1 Approximate Comparison Table
China Taiwan, China Japan South Korea United States International Organization for Standardization Germany France European Standard
GB ISC CNS JIS KS UNS ISO Numerical Grade DIN EN/DIN W-Nr. NF EN/NF EN Numerical Grade
022Cr22Ni5Mo3N
022Cr23Ni5Mo3N 		S22253
S22053 		329J3L SUS 329J3L STS 329J3L S31803
S32205 		X2CrNiMoN 22-5-3 4462-318-03-I X2CrNiMoN 22-5-3 1.4462 X2CrNiMoN 22-5-3 X2CrNiMoN 22-5-3 1.4462
2 Approximate Comparison Table
China United States Germany
GB Commercial Grade UNS W-Nr.
2205 F51 S31803 1.4462
X2CrNiMoN22-5-3 Corresponding Standards(Same grade name, different standards)
1 EN 10088-1-2005
X2CrNiMoN 22-5-3 1.4462
2 EN 10296-2-2005
X2CrNiMoN22-5-3 1.4462
3 EN 10253-4-2003
X2CrNiMoN22-5-3 1.4462
4 EN 10263-5-2001
X2CrNiMoN22-5-3 1.4462
5 EN 10250-4-1999
X2CrNiMoN 22-5-3 1.4462
6 ISO TS 15510-2003
X2CrNiMoN22-5-3
7 EN 10088-3-2005
X2CrNiMoN22-5-3 1.4462
8 ISO 9327(-5)-1999
X2CrNiMoN22-5-3
9 EN 10088-3-2014
X2CrNiMoN22-5-3 1.4462
10 ISO 15510-2014
X2CrNiMoN22-5-3 4462-318-03-I
11 DIN EN 10263-5-2018
X2CrNiMoN22-5-3 1.4462
12 ISO 9328-7-2018
X2CrNiMoN22-5-3
13 DIN EN 10088-3-2014
X2CrNiMoN22-5-3 1.4462
14 DIN EN 10270-3-2012
X2CrNiMoN22-5-3 1.4462
15 ISO 683-18-2014
X2CrNiMoN22-5-3 4462-318-03-I
16 ISO 4954-2018
X2CrNiMoN22-5-3 4462-318-03-I
17 NF EN 10088-2-2005
X2CrNiMoN22-5-3 1.4462
18 NF EN 10088-1-2005
X2CrNiMoN22-5-3 1.4462
19 NF EN 10028-7-2008
X2CrNiMoN22-5-3 1.4462
20 NF EN 10296-2-2005
X2CrNiMoN22-5-3 1.4462
21 NF EN 10028-7-2000
X2CrNiMoN22-5-3 1.4462
22 EN 10263-5-2017
X2CrNiMoN22-5-3 1.4462
23 ISO 4954-2-2024
X2CrNiMoN22-5-3 4462-318-03-I
24 DIN EN 10296-2-2006
X2CrNiMoN22-5-3 1.4462
25 EN 10272-2016
X2CrNiMoN22-5-3 1.4462

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!