X3CrNiMoN 27-5-2 1.4460 - DIN EN 10088-3-2014

Grade	X3CrNiMoN 27-5-2
Germany W-Nr.	1.4460
Corresponding Standard	DIN EN 10088-3-2014 Stainless steels – Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
Classification	Duplex Stainless Steel
Properties	Corrosion Resistance
Density	7.8 g/cm³

X3CrNiMoN 27-5-2 Chemical Element Composition Content (%)

Component	C	Si	Mn	P	S ^ⓑ	Cr	Ni	Mo	N
Minimum Value	-	-	-	-	-	25	4.5	1.3	0.05
Maximum Value	0.05	1	2	0.035	0.03	28	6.5	2	0.2

① Elements not quoted in this table shall not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would impair mechanical properties and the suitability of the steel.

X3CrNiMoN 27-5-2 Mechanical Properties

condition	Heat Treatment or Condition	Tensile Strength σ_b Mpa	Yield Point σ_s Mpa	Elongation or Extension Rate δ %	Hardness HBW	Impact Energy Absorption KV2 J
Bar, rod, wire, section, bright products; d≤160	+AT	620~880	≥450	(long.) ≥20	≤260	(long.) ≥85
Cold drawn, precision bar; d≤10	+AT	770~1030	≥610	≥12
Cold drawn, precision bar; 10<d≤16	+AT	770~1030	≥560	≥12
Cold drawn, precision bar; 16<d≤40	+AT	620~950	≥460	≥15		≥85
Cold drawn, precision bar; 40<d≤63	+AT	620~950	≥460	≥15		≥85
Cold drawn, precision bar; 63<d≤160	+AT	620~880	≥460	≥20		≥85

+AT=solution annealed；+A=annealed；+QT = quenched and tempered；+P=precipitation hardening；+C=Cold worked，+Csuffix followed by a number represents the tensile strength grade, i.e., the minimum tensile strength value.
long.=longitudinal；tr.=transverse
d=diameter or thickness；Unit mm

Approximate Comparison Table

China		United States	International Organization for Standardization		Germany		France	European Standard
GB	ISC	UNS	ISO	Numerical Grade	DIN EN/DIN	W-Nr.	NF EN/NF	EN	Numerical Grade
022Cr25Ni6Mo2N	S22553	S31200	X3CrNiMoN 27-5-2	4460-312-00-I	X3CrNiMoN 27-5-2	1.4460	X3CrNiMoN 27-5-2	X3CrNiMoN 27-5-2	1.4460

X3CrNiMoN27-5-2 Corresponding Standards(Same grade name, different standards)

1	EN 10088-1-2005
	X3CrNiMoN 27-5-2 1.4460
2	EN 10250-4-1999
	X3CrNiMoN 27-5-2 1.4460
3	ISO TS 15510-2003
	X3CrNiMoN27-5-2
4	EN 10088-3-2005
	X3CrNiMoN 27-5-2 1.4460
5	EN 10088-3-2014
	X3CrNiMoN 27-5-2 1.4460
6	ISO 15510-2014
	X3CrNiMoN27-5-2 4460-312-00-I
7	DIN EN 10088-3-2014
	X3CrNiMoN 27-5-2 1.4460
8	ISO 683-18-2014
	X3CrNiMoN27-5-2 4460-312-00-I
9	NF EN 10088-1-2005
	X3CrNiMoN27-5-2 1.4460

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!