X46Cr 13 1.4034 - DIN EN 10088-3-2014

Grade	X46Cr 13
Germany W-Nr.	1.4034
Corresponding Standard	DIN EN 10088-3-2014 Stainless steels – Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
Classification	Martensitic Stainless Steel
Properties	Corrosion Resistance

X46Cr 13 Chemical Element Composition Content (%)

Component	C ^ⓒ	Si	Mn	P	S ^ⓑ	Cr
Minimum Value	0.43	-	-	-	-	12.5
Maximum Value	0.5	1	1	0.04	0.03	14.5

① Elements not quoted in this table shall not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would impair mechanical properties and the suitability of the steel.

X46Cr 13 Mechanical Properties

condition	Heat Treatment or Condition	Tensile Strength σ_b Mpa	Yield Point σ_s Mpa	Elongation or Extension Rate δ %	Hardness HBW	Impact Energy Absorption KV2 J
Bar, rod, wire, section, bright products	+A	≤800			≤245
Bar, rod, wire, section, bright products; d≤160	+QT800	800~1000	≥650	(long.) ≥10		(long.) ≥12
Cold Drawn, Finely Processed Bar d≤10	+QT850	900~1150	≥700	≥7
Cold drawn, precision bar; 10<d≤16	+QT850	900~1150	≥700	≥7
Cold drawn, precision bar; 16<d≤40	+QT850	850~1100	≥650	≥8		≥12
Cold drawn, precision bar; 40<d≤63	+QT850	850~1000	≥650	≥8		≥12
Cold drawn, precision bar; 63<d≤160	+QT850	850~1000	≥650	≥10		≥12
Cold drawn, precision bar; d≤10	+A	≤950			≤305
Cold drawn, precision bar; 10<d≤16	+A	≤950			≤305
Cold drawn, precision bar; 16<d≤40	+A	≤900			≤280
Cold drawn, precision bar; 40<d≤63	+A	≤840			≤260
Cold drawn, precision bar; 63<d≤160	+A	≤800			≤245
Cold drawn wire; d≥0.05	+C500	500~700
Cold drawn wire; d≥0.05	+C600	600~800
Cold drawn wire; d≥0.05	+C700	700~900
Cold drawn wire; d≥0.05	+C800	800~1000
Cold drawn wire; d≥0.05	+C900	900~1100
Cold drawn wire; d≥0.05	+C1000	1000~1250
Cold drawn wire; d≥0.05	+C1100	1100~1350
Cold drawn wire; d≥0.05	+C1200	1200~1450
Cold drawn wire; d≥0.05	+C1400	1400~1700
Cold drawn wire; d≥0.05	+C1600	1600~1900
Cold drawn wire; d≥0.05	+C1800	1800~2100
Cold drawn wire; 0.5<d≤1	+A	≤1100		≥10
Cold drawn wire; 1<d≤3	+A	≤1050		≥10
Cold drawn wire; 3<d≤5	+A	≤1000		≥10
Cold-drawn wire; 5<d≤16	+A	≤950		≥15

+AT=solution annealed；+A=annealed；+QT = quenched and tempered；+P=precipitation hardening；+C=Cold worked，+Csuffix followed by a number represents the tensile strength grade, i.e., the minimum tensile strength value.
long.=longitudinal；tr.=transverse
d=diameter or thickness；Unit mm

New and Old Grade Replacement List

Corresponding Standard	Grade
DIN 17440-1972	Grade Germany W-Nr. Other Name
DIN EN 10088-3-2014	Grade Germany W-Nr.

1 Approximate Comparison Table

Germany		France	European Standard		United Kingdom
DIN EN/DIN	W-Nr.	NF EN/NF	EN	Numerical Grade	BS EN/BS
X46Cr 13 (X40Cr 13)	1.4034	Z38C 13M	X46Cr13	1.4034	420S45

2 Approximate Comparison Table Heat-resistant cast steels and alloys

Japan	United States		Germany		France
JIS	ASTM	UNS	DIN EN/DIN	W-Nr.	NF EN/NF
SCH1 SCH3	CA-40	J91153	G-X40Cr13	1.4034	Z30C13-M Z2813-M

X46Cr13 Corresponding Standards(Same grade name, different standards)

1	EN 10088-1-2005
	X46Cr 13 1.4034
2	ISO TS 15510-2003
	X46Cr13
3	DIN 17440-1972
	X46Cr 13 X40Cr 13 1.4034
4	EN 10088-3-2005
	X46Cr13 1.4034
5	EN 10088-3-2014
	X46Cr 13 1.4034
6	ISO 15510-2014
	X46Cr13 4034-420-00-I
7	NF A 35-565-1994
	X46Cr13
8	DIN EN 10088-3-2014
	X46Cr 13 1.4034
9	NF EN 10088-2-2005
	X46Cr13 1.4034
10	NF EN 10088-1-2005
	X46Cr13 1.4034

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!