中文版
Home Material DIN EN 10088-3-2014
简体 | 繁體
Grade X5NiCrTiMoVB 25-15-2
Germany W-Nr. 1.4606
Corresponding Standard DIN EN 10088-3-2014
Stainless steels – Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
Classification Precipitation-Hardening Stainless Steel
Properties Corrosion Resistance
Density 7.9 g/cm3
X5NiCrTiMoVB 25-15-2 Chemical Element Composition Content (%)
Component C Si Mn P S Cr Ni Mo Ti V B Al
Minimum Value - - 1 - - 13 24 1 1.9 0.1 0.001 -
Maximum Value 0.08 1 2 0.025 0.015 16 27 1.5 2.3 0.5 0.01 0.35
① Elements not quoted in this table shall not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would impair mechanical properties and the suitability of the steel.
X5NiCrTiMoVB 25-15-2 Mechanical Properties
condition Heat Treatment or Condition
Tensile Strength
σb
Mpa 		Yield Point
σs
Mpa 		Elongation or Extension Rate
δ
% 		Hardness
HBW 		Impact Energy Absorption
KV2
J
Bar, rod, wire, section, bright products; d≤50 +AT ≤700 ≥250 ≥35 ≤212
Bar, rod, wire, section, bright products; d≤50 880 880~1150 ≥550 (long.)
≥20		 (long.)
≥50
Cold drawn, precision bar; d≤10 +P880 950~1200 ≥750 ≥15 ≥30
Cold drawn, precision bar; 10<d≤16 +P880 950~1150 ≥750 ≥15 ≥30
Cold drawn, precision bar; 16<d≤40 +P880 900~1150 ≥600 ≥18 ≥40
Cold Drawn, Precision Finished Bar; 40<d≤50 +P880 880~1150 ≥550 ≥20 ≥40
Cold drawn, precision bar; d≤10 +A ≤850 ≤240
Cold drawn, precision bar; 10<d≤16 +A ≤800 ≤230
Cold drawn, precision bar; 16<d≤40 +A ≤800 ≤230
Cold Drawn, Precision Finished Bar; 40<d≤50 +A ≤700 ≤212
Cold drawn wire; d≥0.05 +C500 500~700
Cold drawn wire; d≥0.05 +C600 600~800
Cold drawn wire; d≥0.05 +C700 700~900
Cold drawn wire; d≥0.05 +C800 800~1000
Cold drawn wire; d≥0.05 +C900 900~1100
Cold drawn wire; d≥0.05 +C1000 1000~1250
Cold drawn wire; d≥0.05 +C1100 1100~1350
Cold drawn wire; d≥0.05 +C1200 1200~1450
Cold drawn wire; d≥0.05 +C1400 1400~1700
Cold drawn wire; d≥0.05 +C1600 1600~1900
Cold drawn wire; d≥0.05 +C1800 1800~2100
Cold drawn wire; 0.5<d≤1 +AT ≤1100 ≥10
Cold drawn wire; 1<d≤3 +AT ≤1050 ≥10
Cold drawn wire; 3<d≤5 +AT ≤1000 ≥10
Cold-drawn wire; 5<d≤16 +AT ≤950 ≥15
+AT=solution annealed；+A=annealed；+QT = quenched and tempered；+P=precipitation hardening；+C=Cold worked，+Csuffix followed by a number represents the tensile strength grade, i.e., the minimum tensile strength value.
long.=longitudinal；tr.=transverse
d=diameter or thickness；Unit mm
X5NiCrTiMoVB25-15-2 Corresponding Standards(Same grade name, different standards)
1 EN 10088-1-2005
X5NiCrTiMoVB 25-15-2 1.4606
2 EN 10088-3-2014
X5NiCrTiMoVB 25-15-2 1.4606
3 DIN EN 10088-3-2014
X5NiCrTiMoVB 25-15-2 1.4606
4 NF EN 10088-1-2005
X5NiCrTiMoVB25-15-2 1.4606

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!