中文版
Home Material ISO 683-18-2014
简体 | 繁體
Grade X6CrNiTi18-10
ISO Numeric Designation 4541-321-00-I
Corresponding Standard ISO 683-18-2014
Bright steel products
Classification Austenitic Stainless Steel
X6CrNiTi18-10 Chemical Element Composition Content (%)
Component C Si Mn P S Cr Ni More
Minimum Value - - - - - 17 9 Ti：5C~0.70
Maximum Value 0.08 1 2 0.045 0.03 19 12
X6CrNiTi18-10 Mechanical Properties
Tensile Strength
σb
Mpa 		Yield Point
σs
Mpa 		Elongation or Extension Rate
δ
% 		Impact Energy Absorption
KV2
J
t≤10 600~950 ≥400 （long.）
≥25
10＜t≤16 580~950 ≥380 ≥25
16＜t≤40 500~850 ≥190 ≥30 (long.)
≥100
40＜t≤63 500~850 ≥190 ≥30 ≥100
63＜t≤160 500~700 ≥190 ≥40 ≥100
1 Approximate Comparison Table
China Taiwan, China Japan South Korea United States International Organization for Standardization Germany France European Standard Russia Sweden United Kingdom
GB ISC CNS JIS KS ASTM UNS ISO Numerical Grade DIN EN/DIN W-Nr. NF EN/NF EN Numerical Grade GOST SS BS EN/BS
06Cr18Ni11Ti S32168 321 SUS 321 STS 321 321 S32100 X6CrNiTi 18-10 4541-321-00-I X6CrNiTi 18-10
(X10CrNiTi 18-9) 		1.4541 Z6CNT 18-10 X6CrNiTi 18-10 1.4541 09Х18Н10Т
Х18Н10Т 		2337 321S12
321S31
2 Approximate Comparison Table
China Taiwan, China Japan South Korea United States International Organization for Standardization Germany France European Standard Russia Sweden United Kingdom
GB ISC CNS JIS KS ASTM UNS ISO DIN EN/DIN W-Nr. NF EN/NF EN Numerical Grade GOST SS BS EN/BS
06Cr18Ni11Ti
(0Cr18Ni11Ti) 		S32168 321 SUS 321 STS 321 321 S32100 X6CrNiTi 18-10 X6CrNiTi 18-10
(X10CrNiTi 18-9) 		1.4541 Z6CNT 18-10 X6CrNiTi 18-10 1.4541 09Х18Н10Т 2337 321S12
321S31
3 Approximate Comparison Table Stainless steels for cold heading and cold extruding
China Japan United States International Organization for Standardization European Standard
GB ISC JIS ASTM/AISI UNS ISO Numerical Grade EN Numerical Grade
06Cr18Ni11Ti
(0Cr18Ni11Ti) 		S32168 SUS321 321 S32100 X6CrNiTi18-10 4541-321-00-I X6CrNiTi18-10 1.4541
X6CrNiTi18-10 Corresponding Standards(Same grade name, different standards)
1 EN 10088-1-2005
X6CrNiTi 18-10 1.4541
2 EN 10296-2-2005
X6CrNiTi18-10 1.4541
3 EN 10253-4-2003
X6CrNiTi18-10 1.4541
4 EN 10263-5-2001
X6CrNiTi18-10 1.4541
5 EN 10250-4-1999
X6CrNiTi 18-10 1.4541
6 ISO TS 15510-2003
X6CrNiTi18-10
7 EN 10088-2-2005
X6CrNiTi18-10 1.4541
8 EN 10088-3-2005
X6CrNiTi 18-10 1.4541
9 ISO 9327(-5)-1999
X6CrNiTi18-10 (F53)
10 EN 10088-3-2014
X6CrNiTi 18-10 1.4541
11 ISO 15510-2014
X6CrNiTi18-10 4541-321-00-I
12 DIN EN 10263-5-2018
X6CrNiTi18-10 1.4541
13 ISO 9328-7-2018
X6CrNiTi18-10
14 DIN EN 10088-3-2014
X6CrNiTi 18-10 1.4541
15 ISO 683-18-2014
X6CrNiTi18-10 4541-321-00-I
16 ISO 4954-2018
X6CrNiTi18-10 4541-321-00-I
17 NF EN 10088-2-2005
X6CrNiTi18-10 1.4541
18 NF EN 10088-1-2005
X6CrNiTi18-10 1.4541
19 NF EN 10028-7-2008
X6CrNiTi18-10 1.4541
20 NF EN 10296-2-2005
X6CrNiTi18-10 1.4541
21 NF EN 10028-7-2000
X6CrNiTi18-10 1.4541
22 EN 10263-5-2017
X6CrNiTi18-10 1.4541
23 ISO 4954-2-2024
X6CrNiTi18-10 4541-321-00-I
24 DIN EN 10296-2-2006
X6CrNiTi18-10 1.4541

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!