中文版
Home Material NF EN 10088-2-2005
简体 | 繁體
Grade X6CrNiTi18-10
1.4541
Corresponding Standard NF EN 10088-2-2005
Part2:Technical Delivery Conditions for Sheet/Plate and Strip of Corrosion Resisting Steels for General Purposes
Classification Austenitic Stainless Steel
X6CrNiTi18-10 Chemical Element Composition Content (%)
Component C Si Mn P S ① Cr Ni More
Minimum Value - - - - - 17 9 Ti：5×C~0.7
Maximum Value 0.08 1 2 0.045 0.015 19 12
◎ Elements not listed in this table shall not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All appropriate precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would impair mechanical properties and the suitability of the steel.
X6CrNiTi18-10 Mechanical Properties
condition Heat Treatment or Condition
Tensile Strength
σb
Mpa 		Yield Point
σs
Mpa 		Elongation or Extension Rate
δ
% 		Impact Energy Absorption
KV2
J
Cold rolled strip steel: T ≤ 8mm +AT 520~720 ( t )
Rp0.2：≥ 220①③
Rp1.0：≥ 250①②
③		 ( t )
T＜3mm：≥40③④
T ≥ 3mm：≥40③⑤		 -
Hot rolled strip steel: T ≤ 13.5mm +AT 520~720 ( t )
Rp0.2：≥ 200①③
Rp1.0：≥ 240①②
③		 ( t )
T＜3mm：≥40③④
T ≥ 3mm：≥40③⑤		 （T＞10mm）
I：≥ 100；t：≥60
Hot rolled medium and thick plates: T ≤ 75mm +AT 500~700 ( t )
Rp0.2：≥ 200①③
Rp1.0：≥ 240①②
③		 ( t )
T＜3mm：≥40③④
T ≥ 3mm：≥40③⑤		 （T＞10mm）
I：≥ 100；t：≥60
Steel (Process Flow 2H): Cold Work + C700⑦⑧ 700~850
Steel (Process Flow 2H): Cold Work + C850⑦⑧ 850~1000
Steel (Process Flow 2H): Cold Work + CP350⑦⑧ 350~500
Steel (Process Flow 2H): Cold Work + CP500⑦⑧ 500~700
◎ T-thickness；l-longitudinal；t-trasverse
◎ +A=soft annealed；+QT=quenched and tempered；+P=precipitation hardened；+AT=solutiong annealed；+SR=strength relieved
X6CrNiTi18-10 Corresponding Standards(Same grade name, different standards)
1 EN 10088-1-2005
X6CrNiTi 18-10 1.4541
2 EN 10296-2-2005
X6CrNiTi18-10 1.4541
3 EN 10253-4-2003
X6CrNiTi18-10 1.4541
4 EN 10263-5-2001
X6CrNiTi18-10 1.4541
5 EN 10250-4-1999
X6CrNiTi 18-10 1.4541
6 ISO TS 15510-2003
X6CrNiTi18-10
7 EN 10088-2-2005
X6CrNiTi18-10 1.4541
8 EN 10088-3-2005
X6CrNiTi 18-10 1.4541
9 EN 10297(2)-2005
X6CrNiTi18-10 1.4541
10 ISO 9327(-5)-1999
X6CrNiTi18-10 (F53)
11 EN 10088-3-2014
X6CrNiTi 18-10 1.4541
12 ISO 15510-2014
X6CrNiTi18-10 4541-321-00-I
13 DIN EN 10263-5-2018
X6CrNiTi18-10 1.4541
14 ISO 9328-7-2018
X6CrNiTi18-10
15 DIN EN 10088-3-2014
X6CrNiTi 18-10 1.4541
16 ISO 683-18-2014
X6CrNiTi18-10 4541-321-00-I
17 ISO 4954-2018
X6CrNiTi18-10 4541-321-00-I
18 NF EN 10088-2-2005
X6CrNiTi18-10 1.4541
19 NF EN 10088-1-2005
X6CrNiTi18-10 1.4541
20 NF EN 10028-7-2008
X6CrNiTi18-10 1.4541
21 NF EN 10296-2-2005
X6CrNiTi18-10 1.4541
22 NF EN 10028-7-2000
X6CrNiTi18-10 1.4541
23 EN 10263-5-2017
X6CrNiTi18-10 1.4541
24 ISO 4954-2-2024
X6CrNiTi18-10 4541-321-00-I
25 DIN EN 10296-2-2006
X6CrNiTi18-10 1.4541
26 EN 10272-2016
X6CrNiTi18-10 1.4541
27 EN 10217-7-2021
X6CrNiTi 18-10 1.4541
28 EN 10088-2-2024
X6CrNiTi18-10 1.4541
29 EN 10028-7-2016
X6CrNiTi18-10 1.4541

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!