中文版
Home Material EN 12166-1998
简体 | 繁體
Grade CuZn39Pb0.5
European Standard Steel Grade CW610N
Corresponding Standard EN 12166-1998
Copper and copper alloys — Wire for general purposes
Classification Copper and Copper Alloys
Density 8.4 g/cm3
CuZn39Pb0.5 Chemical Element Composition Content (%)
Component Fe Ni Cu Pb Al Sn Other Total More
Minimum Value - - 59 0.2 - - - Zn:余量
Maximum Value 0.2 0.3 60 0.8 0.05 0.2 0.2
"Other individual elements or other totals": The chemical composition includes elements not specified in the table. Analysis should only be conducted if these elements are suspected to be present, or if routine analysis suggests that their content may exceed the prescribed limits.
CuZn39Pb0.5 Mechanical Properties
diameter③
d
mm		 Mark
Heat Treatment or Condition
Tensile Strength
σb
Mpa 		Yield Point
σs
Mpa 		Elongation or Extension Rate
δ
% 		Hardness
HBW
0.5≤d≤1.5 CuZn39Pb0.5-R400 1/4 Hard; R400 ≥400 ≈200*
1.5<d≤4 CuZn39Pb0.5-R400 1/4 Hard; R400 ≥400 ≈200* ≥10(A100)
1.5≤d≤4 CuZn39Pb0.5-H110 1/4 Hard; H110 HV: 110~140
4<d≤8 CuZn39Pb0.5-R390 1/4 Hard; R390 ≥390 ≈180* ≥15(A11.3)
8<d≤20 CuZn39Pb0.5-R380 1/4 Hard; R380 ≥380 ≈180* ≥20(A)
4<d≤20 CuZn39Pb0.5-H100 1/4 Hard; H100 HV: 100~130
0.5≤d≤1.5 CuZn39Pb0.5-R450 1/2 Hard; R450 ≥450 ≈300*
1.5<d≤4 CuZn39Pb0.5-R440 1/2 Hard; R440 ≥440 ≈300* ≥8(A100)
1.5≤d≤4 CuZn39Pb0.5-H130 1/2 Hard; H130 HV: 130~160
4<d≤8 CuZn39Pb0.5-R430 1/2 Hard; R430 ≥430 ≈300* ≥10(A11.3)
8<d≤20 CuZn39Pb0.5-R420 1/2 Hard; R420 ≥420 ≈300* ≥15(A)
4<d≤20 CuZn39Pb0.5-H120 1/2 Hard; H120 HV: 120~155
0.5≤d≤1.5 CuZn39Pb0.5-R500 Hard; R500 ≥500 ≈400*
1.5<d≤4 CuZn39Pb0.5-R500 Hard; R500 ≥500 ≈400* ≥4(A100)
1.5≤d≤4 CuZn38Pb2-H150 Hard; H150 HV: 150~180
4<d≤8 CuZn38Pb2-R490 Hard; R490 ≥490 ≈400* ≥5(A11.3)
8<d≤14 CuZn39Pb0.5-R480 Hard; R480 ≥480 ≈400* ≥8(A)
4<d≤14 CuZn39Pb0.5-H140 Hard; H140 HV: 140~170
1.5<d≤4 CuZn39Pb0.5-R570 Tough and Hard; R570 ≥570 ≈520*
1.5<d≤4 CuZn39Pb0.5-H165 Tough and Hard; H165 HV: ≥165
All specifications CuZn39Pb0.5-M M No specification No specification No specification No specification
①Material condition designation: H-Hardness (Brinell or Vickers), the suffix number indicates the hardness value; R-Tensile strength, the suffix number indicates the minimum tensile strength; M-As manufactured, without specified mechanical properties
②A100, A11.3, A-gauge length
③Or equivalent cross-sectional area for polygonal wire.
1 Approximate Comparison Table Copper and Copper Alloy
Japan United States International Organization for Standardization Germany France European Standard Russia Sweden United Kingdom
JIS UNS ISO DIN EN/DIN NF EN/NF EN Numerical Grade GOST SS BS EN/BS
C3501 C36500 CuZn37Pb1 CuZn39Pb0.5 CuZn39Pb0.8 CuZn37Pb1 CW605N LS60-1 CuZn40Pb CZ123
2 Approximate Comparison Table Copper and Copper Alloy
Germany European Standard
DIN EN/DIN W-Nr. EN Numerical Grade
CuZn39Pb0.5 2.0372 CuZn39Pb0.5 CW610N
CuZn39Pb0.5 Corresponding Standards(Same grade name, different standards)
1 EN 12166-1998
CuZn39Pb0.5 CW610N
2 DIN EN 12166-1998
CuZn39Pb0.5 CW610N
3 DIN 17660-1983
CuZn39Pb0.5 2.0372 Ms60Pb
4 EN 12164-2016
CuZn39Pb0.5 CW610N
5 EN 12167-2024
CuZn39Pb0.5 CW610N

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!