中文版
Home Material JIS H 4000-2022
简体 | 繁體
Grade A2014P
2014
Corresponding Standard JIS H 4000-2022
Aluminium and Aluminium Alloy Sheets, Strips and Plates
Classification Aluminum and Aluminum Alloys
A2014P Chemical Element Composition Content (%)
Component Fe Si Mn Cr Cu Ti Zn Mg Other Individual Other Total More
Minimum Value - 0.5 0.4 - 3.9 - - 0.2 - - Al: 余量
Maximum Value 0.7 1.2 1.2 0.1 5 0.15 0.25 0.8 0.05 0.15
"Other individual elements or other totals": The chemical composition includes elements not specified in the table. Analysis should only be conducted if these elements are suspected to be present, or if routine analysis suggests that their content may exceed the prescribed limits.
A2014P Mechanical Properties
thickness
t
mm		 Mark
Heat Treatment or Condition
Tensile Strength
σb
Mpa 		Yield Point
σs
Mpa 		Elongation or Extension Rate
δ
% 		Deflection f
mm
0.4≤t≤0.5 A2014P-O O ≤220 ≤140 ≥16 0.4 ≤ t ≤ 1.6
Bending inner diameter: 0.5t
0.5＜t≤13 ≤220 ≤140 ≥16 1.6 < t ≤ 2.9
Bending inner diameter: t
13＜t≤25 ≤220 ≤140 A50mm: ≥10
A: ≥9		 2.9 < t ≤ 6
Bending inner diameter: 1.5t
0.4≤t≤0.5 A2014P-T3 T3 ≥395 ≥245 ≥14 0.4 ≤ t ≤ 0.5
Bending Inner Diameter: 1.5t
0.5＜t≤6 ≥395 ≥245 ≥14 0.5 < t ≤ 1.6
Bending Inner Diameter: 2.5t
6＜t≤6.3 ≥395 ≥240 ≥14 1.6 < t ≤ 2.9
Bending Inner Diameter: 3t
6.3＜t≤12 ≥395 ≥235 ≥13 2.9 < t ≤ 6
Bending Inner Diameter: 3.5t
0.4≤t≤0.5 A2014P-T4 T4 ≥395 ≥240 ≥14 0.4 ≤ t ≤ 0.5
Bending Inner Diameter: 1.5t
0.5＜t≤6 ≥395 ≥240 ≥14 0.5 < t ≤ 1.6
Bending Inner Diameter: 2.5t
6＜t≤6.3 ≥400 ≥250 ≥14 1.6 < t ≤ 2.9
Bending Inner Diameter: 3t
6.3＜t≤12 ≥400 ≥250 ≥14 2.9 < t ≤ 6
Bending Inner Diameter: 3.5t
6≤t≤13 A2014P-T451 T451 ≥400 ≥250 ≥14
13＜t≤25 ≥400 ≥250 ≥14
25＜t≤50 ≥400 ≥250 A50mm: ≥12
A: ≥10
50＜t≤80 ≥395 ≥250 A50mm: ≥8
A: ≥7
0.4≤t≤0.5 A2014P-T42 T42 ≥400 - ≥14
0.5＜t≤25 ≥400 ≥235 ≥14
0.4≤t≤0.5 A2014P-T6 T6 ≥440 ≥390 ≥6 0.4 ≤ t ≤ 0.5
Bending inner diameter: 3t
0.5＜t≤1 ≥440 ≥390 ≥6 0.5 < t ≤ 1.6
Bending inner diameter: 3.5t
1＜t≤6 ≥440 ≥390 ≥7 1.6 < t ≤ 2.9
Bending inner diameter: 4.5t
6＜t≤6.3 ≥450 ≥395 ≥7 2.9 < t ≤ 6
Bending inner diameter: 5t
6.3＜t≤12 ≥450 ≥395 ≥7
0.4≤t≤0.5 A2014P-T62 T62 ≥440 - ≤6
0.5＜t≤1.0 ≥440 ≥390 ≥6
1.0＜t≤6.5 ≥460 ≥400 ≥7
6.5＜t≤13 ≥460 ≥410 ≥7
13＜t≤25 ≥460 ≥410 ≥6
6.0≤t≤13 A2014P-T651 T651 ≥460 ≥405 ≥7
13＜t≤25 ≥460 ≥405 A50mm: ≥7
A: ≥6
25＜t≤50 ≥460 ≥405 A50mm: ≥4
A: ≥5
50＜t≤60 ≥450 ≥390 A50mm: ≥2
A: ≥3
60＜t≤80 ≥435 ≥380 A50mm: ≥2
A: ≥1
80＜t≤100 ≥405 ≥380 A: ≥1

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!