2024 A2024 W A2024 BD - JIS H 4040-2006

Grade	2024
Other Names
Corresponding Standard	JIS H 4040-2006 Aluminium and aluminium alloy rods, bars and wires
Classification	Aluminum and Aluminum Alloys
Properties	Strength Machinability

2024 Chemical Element Composition Content (%)

Component	Fe	Si	Mn	Cr	Cu	Ti	Zn	Mg	Other Individual	Other Total	More
Minimum Value	-	-	0.3	-	3.8	-	-	1.2	-	-	Al:余量
Maximum Value	0.5	0.5	0.9	0.1	4.9	0.15	0.5	1.8	0.05	0.15	Al:余量

"Other individual elements or other totals": The chemical composition includes elements not specified in the table. Analysis should only be conducted if these elements are suspected to be present, or if routine analysis suggests that their content may exceed the prescribed limits.

2024 Mechanical Properties

diameter/thickness/width across flats/cross section area d/s mm	Heat Treatment or Condition	Tensile Strength σ_b Mpa	Yield Point σ_s Mpa	Elongation or Extension Rate δ %
d≤3	Annealing (O)	≤245
3＜d≤100	Annealing (O)	≥245		≥16
12.5＜d≤100	Solution treatment + stress relief + natural aging (T351)	≥425	≥310	≥9
d≤3	Solution treatment + stress relief + natural aging (T4, T451)	≥425
3<d≤12	Solution treatment + stress relief + natural aging (T4, T451)	≥425	≥310	≥10
12＜d≤100	Solution treatment + stress relief + natural aging (T4, T451)	≥425	≥290	≥10
d≤3	Solution Treatment + Natural Aging (T42)	≥430
3＜d≤100；s≤230	Solution Treatment + Natural Aging (T42)	≥430	≥275	≥10
d≤3	Solution heat treatment + artificial aging hardening (T62)	≥410
3＜d≤100；s≤230	Solution heat treatment + artificial aging hardening (T62)	≥410	≥315	≥5

d: diameter, thickness or width across flats；unit mm
s: cross section area; unit cm²
A、A50mm-gauge length

1 Approximate Comparison Table Wrought aluminum and aluminum alloy

China	Japan	United States		International Organization for Standardization		Germany		European Standard
GB	JIS	ASTM	UNS	ISO	Numerical Grade	DIN EN/DIN	W-Nr.	EN
2024	2024 A92024	2024	A92024	AlCu4Mg1	A92024	AlCu4Mg2	3.1355 A92024	EN-AW-AlCu4Mg1

2 Approximate Comparison Table Aluminium and aluminium alloy

Japan	United States	International Organization for Standardization	Germany		France	European Standard	Russia	United Kingdom
JIS	ASTM	ISO	DIN EN/DIN	W-Nr.	NF EN/NF	EN	GOST	BS EN/BS
2024	2024	AlCu4Mg1	AlCuMg2	3.1355	2024	ENAW-AlCu4Mg1	D16	2024

2024 Corresponding Standards(Same grade name, different standards)

1	GB /T 3190-2008
	2024
2	JIS H 4040-2006
	2024 A2024 W A2024 BD
3	GB /T 3195-2016
	2024
4	DIN 1725-1-1983
	2024 AlCuMg2 3.1355
5	GB /T 3190-2020
	2024
6	JIS H 4040-2015
	2024 A2024 BE
7	GB /T 3191-2019
	2024
8	SAE AMS-QQ-A-250/4A-2007
	2024 A92024
9	GJB 1741-1993
	2024 (LY12) 2A12
10	GB /T 3880.1-2012
	2024

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!