C60 - JIS G 7105-2000

Grade	C60
Corresponding Standard	JIS G 7105-2000 Heat-Treatable Steels, Alloy Steels and Free-Cutting Steels — Part 18 : Bright Products Of Unalloyed and Low Alloy Steels
Classification	Carbon Steel
Properties	Carburizing Ability

C60 Chemical Element Composition Content (%)

Component	C	Si	Mn	P	S
Minimum Value	0.57	0.1	0.6	-	-
Maximum Value	0.65	0.4	0.9	0.045	0.045

◎ Steels with machinability which has been improved either by the addition of lead or by higher sulfur levels up to about 0.100 % (m/m) S (including controlled sulfide morphology) may be available on request.

C60 Mechanical Properties

thickness t mm	Heat Treatment or Condition	Tensile Strength σ_b Mpa	Yield Point σ_s Mpa	Elongation or Extension Rate δ %	Hardness HBW
t≤5	TC	≥860	≥700	≥4
5＜t≤10	TC	≥840	≥630	≥5
10＜t≤16	TC	≥800	≥570	≥5
16＜t≤25	TC	≥740	≥520	≥5
25＜t≤40	TC	≥720	≥480	≥6
40＜t≤100	TC	≥670	≥340	≥7
t≤100	TC+TA, P+TA or G+TA				≥241
t≤16	TC+TN, P+TN or G+TN	≥710	≥380	≥10
16＜t≤100	TC+TN, P+TN or G+TN	≥670	≥340	≥11
100＜t≤250	TC+TN, P+TN or G+TN	≥650	≥310	≥11
t≤16	TC+TQ+TT℗, P+TQ+TT or G+TQ+TT	850~1000	≥580	≥11
16＜t≤40	TC+TQ+TT℗, P+TQ+TT or G+TQ+TT	800~950	≥520	≥13
40＜t≤100	TC+TQ+TT℗, P+TQ+TT or G+TQ+TT	750~900	≥450	≥13
100＜t≤250	TC	Be agreed	Be agreed	Be agreed
100＜t≤250	TC+TA, P+TA or G+TA				Be agreed
100＜t≤250	TC+TQ+TT, P+TQ+TT or G+TQ+TT	Be agreed	Be agreed	Be agreed

C60 Corresponding Standards(Same grade name, different standards)

1	ISO 683-18-1996
	C60
2	DIN 17200-1987
	C60 1.0601
3	ISO 683-1-1987
	C60
4	EN 10083-2-2006
	C60 1.0601
5	EN 10250-2-2000
	C60 1.0601
6	EN 10277-2-2008
	C60 1.0601
7	DIN 17222-1979
	C60 1.0601
8	DIN 17204-1990
	C60 1.0601
9	ISO 683-1-2016
	C60
10	DIN EN ISO 683-1-2018
	C60
11	ISO 683-18-2014
	C60
12	DIN 1652-1963
	C60 1.0601
13	NF EN 10083-2-2006
	C60 1.0601
14	NF A 37-502-1984
	C60
15	JIS G 7105-2000
	C60

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!