XM-13 S13800 - ASTM A693-2024

Grade	XM-13
USA UNS	S13800
Corresponding Standard	ASTM A693-2024 Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
Classification	Precipitation-Hardening Stainless Steel

XM-13 Chemical Element Composition Content (%)

Component	C	Si	Mn	P	S	Cr	Ni	Mo	N	Al
Minimum Value	-	-	-	-	-	12.3	7.5	2	-	0.9
Maximum Value	0.05	0.1	0.2	0.01	0.008	13.2	8.5	2.5	0.01	1.35

XM-13 Mechanical Properties

Thickness t in.	Heat Treatment or Condition	Tensile Strength σ_b Mpa	Yield Point σ_s Mpa	Elongation or Extension Rate δ %	Hardness HBW
0.0015~4.00	Solid Solution Treatment	/	/	/	HRC ≤38
t＜0.02	Precipitation Hardening, 510℃	≥1515	≥1410	≥6	HRC ≥45
0.02~0.1874	Precipitation Hardening, 510℃	≥1515	≥1410	≥8	HRC ≥45
0.1875~0.625	Precipitation Hardening, 510℃	≥1515	≥1410	≥10	HRC ≥45
0.626~4.0	Precipitation Hardening, 510℃	≥1515	≥1410	≥10	HRC ≥45
t＜0.02	Precipitation Hardening, 538°C	≥1380	≥1310	≥6	HRC ≥43
0.02~0.1874	Precipitation Hardening, 538°C	≥1380	≥1310	≥8	HRC ≥43
0.1875~0.625	Precipitation Hardening, 538°C	≥1380	≥1310	≥10	HRC ≥43
0.626~4.0	Precipitation Hardening, 538°C	≥1380	≥1310	≥10	HRC ≥43

Note：Reduction of Area：Applicable to tests in the long transverse direction. Transverse to the direction of rolling and parallel to the product surface.
Note：Impact test is not required unless specified on the purchase order.

Approximate Comparison Table Precipitation Hardening Stainless Steel

China		United States		International Organization for Standardization		European Standard
GB	ISC	ASTM	UNS	ISO	Numerical Grade	EN	Numerical Grade
04Cr13Ni8Mo2Al GB/T 20878-2024	S51380	XM-13 ASTM A959	S13800	X3CrNiMoAl13-8-3 ISO 15510	4534-138-00-X	X3CrNiMoAl13-8-3 EN 10088-1	1.4534

XM-13 Corresponding Standards(Same grade name, different standards)

1	ASTM A959-2004
	XM-13 S13800
2	ASTM A564/A564M-2019(a)
	XM-13 S13800
3	ASTM A693-2013
	XM-13 S13800
4	ASTM F899-2020
	XM-13 S13800
5	ASTM A959-2019
	XM-13 S13800
6	ASTM A705/A705M-2023
	XM-13 S13800
7	ASTM A693-2024
	XM-13 S13800

Note: The data is for reference only! If you have any questions, please fill out "I want to correct it"!